This ensures that the shotgun action is thoroughly oiled, but not over oiled. Smith (or any shotgun action), I like to first flood the working parts with a high quality gun oil, then blow as much of the oil as possible away with compressed air. It is important however, that the cleaning operation be done thoroughly. We all have our own techniques (every way from solvent and toothbrush to sonic cleaning systems).
LC SMITH SHOTGUN PARTS HOW TO
There is no need for me to tell anyone how to clean a disassembled shotgun action.
LC SMITH SHOTGUN PARTS DRIVER
Removing the firing pin is easily done by carefully grinding a screw driver to fit the bushing.
On some of the older models and on many of the higher grade shotguns, the firing pin is fitted in the receiver with a firing pin bushing. There is generally enough clearance between the stock and the firing pin to remove the firing pin without further disassembly. Smith shotguns, the firing pins are easily removed by taking off the sidelocks. in New York, and can be easily made if necessary on the lathe. They are readily available through the Brownells catalog and from Gun Parts Corp. Smith shotgun are broken firing pins, broken top lever springs, gummed and dirty actions (usually causing the rotating bolt to bind) and short chambers.īroken firing pins are an easy fix. The most common repairs I see on the L.C. It may be necessary to lightly wiggle the butt stock to separate the trigger plate, frame and stock. With the action upside down and secured in a vise and the top lever returned to its closed position, remove the screw attaching the trigger plate to the top lever. Push the top lever to its open position and remove the screw beneath it. Remove both the front and rear trigger plate screws. With the safety off, the triggers should spring rearward and allow you to unscrew the trigger guard from the frame. Nothing could look worse on a fine double-barreled shotgun than screws that have been damaged by screwdrivers that do not fit. I cannot stress enough the importance of using good screw drivers. Using either the long screw or a 1/8-inch punch inserted from the right and through the frame, push the left lock assembly away from the frame.
LC SMITH SHOTGUN PARTS INSTALL
Using the long screw as a handle, install it in the outside of the right sideplate and pull gently until the rear of the plate swings away from the frame. With a well fitted, parallel ground screw driver, remove all of the sidelock screws. If this is the case, the plate assemblies will have to be rebedded. If it is not, this is a sign that the stock of the shotgun has shrunk and that the sideplates may be drawn too closely together by the torque of the rear screw. The threaded end should be relatively flush with the outside of the right plate. The regular framed shotguns use only the longer screw.Įxamine the longer screw before removing it. The featherweight models have their lock assemblies attached by three screws, one in the front of each sideplate (attaching the plates to the frame) and a longer screw installed from the left plate (attaching the sidelocks to each other). Smith will be much easier to remove if the hammers are tucked out of the way as they are when cocked. Normally, gunsmiths want to be sure that a firearm‘s action is not cocked prior to disassembly, but the sidelocks of an L.C. To begin disassembly, open the shotgun to ensure that it is unloaded and that it is cocked. Smith hammerless shotgun is its disassembly, cleaning, oiling and reassembly. Its rotary bolt and extremely strong top lever spring make it a seemingly difficult shotgun to disassemble and put back together, so a good place to start any instruction on the L.C. Smith is one of the most requested services on this shotgun.
This is why cleaning and properly oiling the L.C. Smith shotgun is very sensitive to dirt and foreign matter within its action. If you own a Smith and want to make it suitable to shoot again, or if you are presented a Smith to repair, here’s what you need to know about the shotgun. Smith’s side-lock design have made it a very desirable shotgun for both the sportsman and collector alike, and with the recent conditional approval of bismuth shot, which eases many Smith owners’ worries about steel shot, many of these fine old shotguns will be brought back into service as waterfowl shotguns. The graceful beauty and light construction of the L. Smiths were manufactured by the Hunter Arms Company. Smith Gun Company, but in 1888, the company was bought by John Hunter, Sr., and was moved to Fulton, New York. Smith Hammerless Double was first produced in Syracuse, New York, in 1886 by the L.